Hydraulic Controlled Slow Closing Check Butterfly Valve
The DX7K41X accumulator tank type hydraulic control slow closing check butterfly valve is currently a key control equipment used at the inlet of water turbines, with good sealing and regulating performance. This valve is a new product developed by Qigao Valve in recent years. Through careful investigation and research of various similar products at home and abroad, a unique hydraulic control butterfly valve with three eccentricities as the basic structural type has been created. After field application, the operating system runs well. In addition to the advantages of the three eccentricities structure, this butterfly valve also has the following obvious advantages and features.
main features
1. The driving system of this valve is a two-stage driving device with medium and equal pressure. The device has a small volume and a wide range of control for the opening and closing speed of the butterfly valve. The initial opening section is controlled by high pressure and small flow rate, which makes the butterfly valve open smoothly and without violent fluctuations, completely eliminating the hidden danger of water hammer in the system. Then, it will switch to a faster rotational angular velocity, and the hydraulic cylinder will smoothly open the butterfly plate with the set ideal thrust and speed.
2. The installation position of this butterfly valve is usually horizontal, and the reasonable placement of the butterfly plate deviation position can fully utilize the dynamic water torque in the pipeline to drive the smooth closure of the butterfly plate. The installation position of this valve will reflect the combined effect of dynamic water torque and heavy hammer torque. As the closing angle is gradually completed, the dynamic water torque will tend to decrease, and the heavy hammer torque will make the closing instantaneous slow and smooth, thus strictly preventing the occurrence of water hammer phenomenon. The zero leakage sealing effect will be reliably achieved in this reasonable and tight control system.
3. The electro-hydraulic control system of this valve has remote control function, and the opening and closing of the butterfly plate at any speed and the locking at any position can be easily achieved through various well-designed hydraulic control valves.
4. This valve is equipped with a manual oil pump, which can still close or open the butterfly valve normally in case of power failure due to system reasons.
Model designation of hydraulic control slow closing check valve butterfly valve
Main performance parameters of hydraulic control slow closing check butterfly valve
Model | Nominal Pressure (Mpa) | Experimental Pressure (Mpa) | Applicable Temperature (℃) | Applicable Media | |
Shell Experiment | Sealing est | ||||
DX7K41H-6C | 0.6 | 0.9 | 0.66 | ≤65 | Water |
DX7K41H-10C | 1.0 | 1.5 | 1.1 |
Project | Nominal Diameter | ||
Dn≤1000 | DN≥1400 | ||
Valve Opening Time (S) | 10~60 Adjustable | 15~60 Adjustable | |
Valve Closing Time (S) | Close It Quickly | 1.2~25 Adjustable | 2~30 Adjustable |
Slow off | 2~60 Adjustable | 4~60 Adjustable | |
Valve Closing Angle (°) | Close It Quickly | 60°+10° | |
Slow Off | 25°+10° |
Main component materials of hydraulic control slow closing check butterfly valve
Name and Model | Valve Body | Disc | Butterfly Plate Sealing Ring | Valve Stem | Valve Seat | Filler |
DX7K41H-6/10 Z | Grey Cast Iron | Ductile Iron | Nitrile Rubber | Chromium Stainless Steel | Copper Alloy | O-Ring Rubber |
DX7K41H-6/10 C | Carbon Steel | Carbon Steel | Stainless Steel | Chromium Stainless Steel | Stainless Steel | Flexible Graphite |
Main dimensions and weight of hydraulic control slow closing check butterfly valve
Tel: 15351513006
Landline: 0515-89118577
Fax: 0515-8911 8000
Email: jtongcn 126.com
Address: Oubei Pump and Valve Industrial Park, Binhai Economic Development Zone, Jiangsu Province
15351513006